Greenteeth

Greenteeth
  • Greenteeth

    500 Series LoPro™ Pockets

    The 500 Series is the smallest of our teeth & pockets. The pockets are only available in a straight & an angle. Every LoPro™ pocket is designed to have each a threaded & counter-bored hole, so every pocket can fit on either side of the wheel.

    Introduced in 2006, the LoPro™ series of pockets have a slim design that allows for a 3/4" clearance between the side of the pocket and the stump. This clearance prevents the pocket from rubbing against the stump, which reduces pocket wear and improves overall performance.

    Greenteeth Pockets

    500 Series LoPro Greenteeth®

     

    Greenteeth Logo

    500 Greenteeth
    500 Series
    Greenteeth® Specifications
    Wrench Size (in)Nut Size (in)Carbide (in)Torque (ft. lbs.)
    1/2"5/16" 181/2"20 (27Nm)

     

    Click to see Greenteeth Bolts

    Click to see Machine Setups to suit your machine.

     

    Teeth come with nuts and spacers but if you need extra, they are listed below.

     

    Code: 500TH-G
    From: $0.35 inc GST
  • Greenteeth

     

    700 Series LoPro™ Pockets

    A bit larger than the 500, the 700 Series are available in a straight, angle & reverse. Every LoPro™ pocket is designed to have each a threaded & counter-bored hole, so every pocket can fit on either side of the wheel.

    Introduced in 2006, the LoPro™ series of pockets have a slim design that allows for a 3/4" clearance between the side of the pocket and the stump. This clearance prevents the pocket from rubbing against the stump, which reduces pocket wear and improves overall performance.

    Greenteeth Pockets

     

    Greenteeth Logo

    700 Series Greenteeth® Options

    There are two tooth options available for the 700 series: The original Greenteeth® and our new Wearsharp® teeth.

    The unique design of our Wearsharp® allows the tooth to retain a sharp cutting surface, unlike traditional teeth that tend to round over. This provides a consistent cut throughout the life of the tooth, allowing you to maintain a faster sweep speed.

    While we recommend our Wearsharp® teeth for this series, we do continue to offer the original Greenteeth® series.

    The Wearsharp® Advantage
    Better By Design™

    Greenteeth Logo

    Wearsharp Tooth
    700 Series
    Greenteeth® Specifications
    Wrench Size (in)Nut Size (in)Carbide (in)Torque (ft. lbs.)
    Greenteeth®9/16"3/8" 163/4"25 (34Nm)
    Wearsharp®1/2"5/16" 183/4"20 (27Nm)

     

    Click to see Greenteeth Bolts

    Click to see Machine Setups to suit your machine.

     

    Teeth come with nuts and spacers but if you need extra, they are listed below.

     

     

    Code: 700TH-G
    From: $0.35 inc GST
  • Greenteeth

     

    900 Series LoPro™ Pockets

    The 900 Series are available in a straight, angle, & reverse. Every LoPro® pocket is designed to have each a threaded & counter-bored hole, so every pocket can fit on either side of the wheel.

    Introduced in 2006, the LoPro® series of pockets have a slim design that allows for a 3/4" clearance between the side of the pocket and the stump. This clearance prevents the pocket from rubbing against the stump, which reduces pocket wear and improves overall performance.

    Greenteeth 900 Pockets
    Greenteeth 900 Teeth

    900 Series Greenteeth® Options

    There are four tooth options available for the 900 series: The original Greenteeth®, as well as three options of our new Wearsharp® teeth.

    The unique design of our Wearsharp® allows the tooth to retain a sharp cutting surface, unlike traditional teeth that tend to round over. This provides a consistent cut throughout the life of the tooth, allowing you to maintain a faster sweep speed.

    Because we believe that performance is never a one size fits all scenario, we have done extensive testing & found that we can fine tune performance with slight variations in the design of the teeth. Depending on the size of your wheel and how it cuts, we offer four different versions of the Wearsharp® tooth.

    While we recommend our Wearsharp® teeth for this series, we do continue to offer the original standard dish Greenteeth®

    900 Series Greenteeth® Quick Reference Guide

    CodeDescriptionCompatibility
    900TH-G900 Series Green (standard Dish)900 Series LoPro™ Pockets
    900TH-WS900 Series Wearsharp (23" wheels & larger)900 Series LoPro™ Pockets
    926-WS900 Series Wearsharp (up to 22" wheels)900 Series LoPro™ Pockets
    926-WS2900 Series Wearsharp 2-sided shank
    (up to 22" wheels)
    900 Series LoPro™ Pockets
    Greenwheel & Quadwheel

    .


    The Wearsharp® Advantage
    Better By Design™

    Greenteeth Logo

    Wearsharp Tooth
    900 Series
    Greenteeth® Specifications
    Wrench Size (in)Nut Size (in)Carbide (in)Torque (ft. lbs.)
    Greenteeth®5/8"7/16" 147/8"35 (47Nm)
    Wearsharp®5/8"7/16" 147/8"35 (47Nm)

     

    Click to see Greenteeth Bolts

    Click to see Machine Setups to suit your machine.

     

    Teeth come with nuts and spacers but if you need extra, they are listed below.

     

     

    Code: 900TH-G
    From: $0.40 inc GST
  • GREENWHEEL

    The Greenwheel offers increased productivity along with decreased labor time. Why work harder and longer than necessary?

    The Greenwheel is now available for the following stump grinders: Carlton 2100, Carlton 2300, Carlton 2400, Carlton 2500, Carlton 2700, Carlton 4012, Bandit 2000, Bandit 2100, Bandit 2150, Bandit 2450, Rayco 1625 Super JR., Rayco 1620 JR., Rayco 1631, Rayco 1635 Super JR., Rayco 1635, Vermeer 206, Vermeer 222, Vermeer 252, Vermeer 352, and Vermeer 372.

    Code: GW16
    $2,401.20 inc GST
  • GREENWHEEL

    The Greenwheel offers increased productivity along with decreased labor time. Why work harder and longer than necessary?

    The Greenwheel is now available for the following stump grinders: Carlton 2100, Carlton 2300, Carlton 2400, Carlton 2500, Carlton 2700, Carlton 4012, Bandit 2000, Bandit 2100, Bandit 2150, Bandit 2450, Rayco 1625 Super JR., Rayco 1620 JR., Rayco 1631, Rayco 1635 Super JR., Rayco 1635, Vermeer 206, Vermeer 222, Vermeer 252, Vermeer 352, and Vermeer 372.

    Code: GW352
    $2,401.20 inc GST
  • LoPro™ Bolts

    • Designed specifically to fit the angled shoulder of the LoPro™ pockets
    • 1/2" Allen Drive
    • Smooth shank that reduces wheel wear
    • Extraction slot at the end of the bolt for easy removal in case of breakage
    • All LoPro™ bolts should be torqued from 180 to 200 ft. lbs. (244Nm)
    Code: LP-134
    From: $5.06 inc GST